Need any Wiring Diagrams? (Stereo, Alarm and/or Crusie Control)

[Matt94GT]

Feel free to ask me.  I can get them for basically any vehicle.  Just post here and ill post em up.

Instead of guessing the stereo wires or spending $20 on a vehicle specific harness you can just get the diagrams match them up with your headunit diagrams and your good to go.

-------------------------------------------------------------------------
EXAMPLE
1995-1997 Mustang STEREO WIRING
Constant 12V+   Green/Yellow
Switched 12V+    Yellow/Black
Ground    Black/Green
Illumination Light Blue/Red
Dimmer    n/a
Amplifier Remote Dark Blue
Antenna Right Front

Front Speakers    5" x 7" Doors
Left Front (+)    Orange/Light Green
Left Front (-)    Light Blue/White
Right Front (+) White/Light Green
Right Front (-) Dark Green/Orange

Rear Speakers    5" x 7" Rear Deck
Left Rear (+)    Gray/Light Blue
Left Rear (-)    Tan/Yellow
Right Rear (+)    Orange/Red
Right Rear (-)    Brown/Pink 
---------------------------------------------------------------

I can get these (Stereo Diagrams) as well as Alarm Diagrams, and Crusie Control Diagrams for pretty much any vehicle.

[Lightning Struck]

hey I'm having a little trouble with my mach 460 in my cobra, I think I have a bad connection or something, because every other day or so my rear speakers sound like they are blown.  I have disconnected a plug right in the middle of the trunk area under the seat trim, and then plugged it back in and it goes away only to come back again later.  The previous owner added subs I think because on the back of the rear left seat there a 4 holes that looks like the spot a amp use to be mounted at, also on the left amp harness there is two plastic splice in pieces for external hook ups........maybe he messed something up when he did that? A diagram of the correct wiring would be great, also any suggestions or ideas on this would be terrific.

[wolvee123]

I have a 96 gt vert with a CodeAlarm system in it and for some reason none of my interior lights work.  Someone i spoke with said that the interiors are conceted through the aftermarket alarm and thats where I should check first for wiring problems...  obviously I checked all bulbs and fuses and door switches.  I do have the glovebox light and all dash lights.  What wire digram would i need and can you get it?  THanks
MikeW

[B0mb3r645]

Hey I'm having troubles with my Mach 460 system, and am asking for a diagram so I can look into it without spending money I don't have.

And if you do, do you have both fuse panel diagrams?  Didn't get a car manual when I got the stang.

[Matt94GT]

I dont have the mach460 diagram or at least I dont think it is, unless its the one at the very top in my 1st post (check that out).

Here I hosted up a online shop manual (much better then ford) download it here:
http://www.sn95forums.com/misc/94CAR_06_0.iso.zip

Only thing is that its more so for the 94-95 but it should still have the fuse panel diagrams on there.

[B0mb3r645]

Thanks!  Dl'ed, will take a look at it 2morrow.

[gearhead]

Do you have any for the 96-98 mach sound systems?

[Matt94GT]

no i cant find the mach unless this is it:

1995-1997 Mustang STEREO WIRING
Constant 12V+   Green/Yellow
Switched 12V+    Yellow/Black
Ground    Black/Green
Illumination Light Blue/Red
Dimmer    n/a
Amplifier Remote Dark Blue
Antenna Right Front

Front Speakers    5" x 7" Doors
Left Front (+)    Orange/Light Green
Left Front (-)    Light Blue/White
Right Front (+) White/Light Green
Right Front (-) Dark Green/Orange

Rear Speakers    5" x 7" Rear Deck
Left Rear (+)    Gray/Light Blue
Left Rear (-)    Tan/Yellow
Right Rear (+)    Orange/Red
Right Rear (-)    Brown/Pink 

[gearhead]

Do you know where the amp or amps are for my system??  I think I blew mine out, but I have no idea where to begin troubleshooting.  I have a hane's manual and their diagrams suck, plus they have nothing in there about the sound systems. 

All I did was check the fuse in the fuse panel for it, and it was good.  Any help is appreciated!!

[Matt94GT]

should be in the trunk in either the corner or up top below the windshield.

[luke five oh]

Just lately, I keep blowing the #8 fuse...and I have no idea where or why.... a wiring diagram of everything connected through that fuse and how the wiring is run would be a huge help.... or maybe if this is a common issue or something

[Matt94GT]

Which is fuse #8?  Sorry I dont have a diagram like that.

[luke five oh]

Which is fuse #8?  Sorry I dont have a diagram like that.

Judging from what's not working...itts the courtesy lights, radio, clock pod, speedo amplifier

[Matt94GT]

Do you have a stock stereo?  Any aftermarket gauges?

[luke five oh]

Do you have a stock stereo?  Any aftermarket gauges?

bought the car, it had an aftermarket sony radio....no custom gauges or anything though

[Matt94GT]

If it were me id prob just install a slightly higer amperage fuse, I know thats not right but it will work and if that blows then you know you have a problem you gotta solve on your hands

[MeanGrn Gt]

You dont by chance have a diagram of the third brake light housing for a 95 do ya(didnt think ya pry would but figured id ask)? The previous owner put on a cobra wing and he hacked up the wiring and a couple wires are not hooked up.

[Matt94GT]

I found a diagram of the stereo for the mach:

[Tattoogod]

Hi , Can you check to see if the hazard flasher is the same as the turn signal flasher..I was told they are the same relay with two parts in them..since my airbag light came on..peeps are telling me the clock spring is bad..would this cause the turnsignals stop working...everything else works perfect. I give up  >:(

[Matt94GT]

cant help ya there bud, id just ask ford.  i know my signals work and my airbag light is on...?

[Sonic]

Hey matt can you help me out with a mach1000 wiring diagram? I bought the system from a friend but without the harness...

[Matt94GT]

I posted all i can find in the other thread sorry man.

[Sonic]

No prob. Thanks, though.

[philoldsmobile]

I found a diagram of the stereo for the mach:

hi,

i'm installing an ipod compatible head unit into my SN95 (96 export spec V6) and dont want to use the stock amp..

if i cut and isolate wires 1 and 3 on the power connector, am i right in assuming the amp simply wont function? i am running new speaker cables directly to the speakers from the head unit, as no suitable interface is available over here...

is there any chance of it affecting anything else, all seems fine in a test, but i want ti be sure before i solder / heatshrink everything..

BTW, i have no remote entry or alarm....

[Sonic]

I'd say yes. But you can try without cutting the cables - just pull the plug from the socket and use some cables to bridge 2, 4, 5, 6, 7, 8 and see what happens.

[philoldsmobile]

excelent, thanks..

[kspilly]

Wondering if you can hook me up with the stereo wiring for an 01 Cobra? A friend has one and wants to wire in a new deck without using an adapter. Let me know what you can do.
 

[fatman2k4]

A couple of my friends have Elemental Designs subs and amp...they sound really good and are made to last......and they aren't very expensive.....I'm going to put two of their 10's in my next car.....or maybe a 18"....hehe..

Here's the link to their site...
http://www.edesignaudio.com/edv2/index.php


And here are some videos of their subs.....the videos do no justification of how powerful they are.......click on 'e' and find Elemental Designs...

http://www.realmofexcursion.com/videos.html

[Matt94GT]

yeah ED makes good stuff, I remember I bought one of their lower end subs when they first came out...probably 4 years ago? was a good sub for sure

[Wayne]

I did a down load but my computer says it needs a program to open the file. what program would that be :help2:

[Matt94GT]

no idea what kind of file is it? should say when you right click and see info.

[tgreenwood]

Do you have any wiring diagrams for the mach 460 in a 94 gt? I have no sound from speakers. thanks Travis

[kintek]

Matt do you what the wire specs would be for a 95 3.8 so I can get my alarm hooked up on it myself.  Thanks

[Leroy Brown]

How about tach/oil pressure/temp wiring in the engine bay on a 94 v6?